How to Remove and also Replace a Bathtub.
How to Remove and also Replace a Bathtub.
Blog Article
What are your concepts on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, and occasionally, tiling skills. Replacing an old bath tub with a new one is additionally a reasonably tough task. If the old tub is conveniently available, the task can move immediately; if you need to open a wall surface to remove the old bathtub and position the brand-new tub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will require an assistant to leave the old bathtub and embeded in the brand-new one. Ensure you have actually qualified yourself for the work and fit trying it. Rather than employing a specialist to take over a halfway-completed job, it is better to think about employing one before you start. Possibilities are you might need an expert plumber to make tube connections.
This post will certainly assist you mount a new bath tub in your shower room if you have already acquired a new bathtub and don't require to change the plan of your previous water pipes.
Your devices and also material list should make up the following:
Preparing for the Setup
To start with, the supporting framework provided with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to see to it that if the faucet comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you use every one of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be fitted in its last setting.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be rather problematic because of the restricted accessibility that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric all set for the staying water that will originate from the pipes. When the supply pipes have been removed, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to going on to fit the brand-new faucets, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the bath tub in the required setting. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub till the level reads degree.
To set up taps, fit all-time low of the outermost adaptable tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Switch on the water and also check all joints and also brand-new pipework for leaks as well as tighten them if required. Fill the bath tub as well as additionally inspect the overflow outlet and the normal electrical outlet for leakages.
Lastly, repair the bathroom paneling as defined in the maker's instruction manual. Tiling and sealing around the bath tub must wait up until the bathtub has actually been used at least when as this will certainly resolve it into its final position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the installing hole in the bath/basin guaranteeing that the washers are in area in between the faucet as well as the sink. Protect the tap in place with the manufacturer given backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet ports. The former type needs to be attached to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, causing the water to pass through the wall surface between the bath and the tiling, leading to complications with wetness as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to enable the movement experienced when the tub remains in usage. The sealant can crack fairly very early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently readily available on the market. It is recommended to fit the tiles making use of water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy more info about Tools You Need to Install a New Bathtub ? Write feedback down below. We will be glad to listen to your thoughts about this blog posting. Hoping to see you back again in the near future. Enjoyed our post? Please share it. Help another person check it out. Many thanks for going through it.
Booking Page Report this page